DIY Shoe Storage Bench | How to Build

DIY Shoe Storage Bench | How to Build

What’s up guys? I’m brad from Fix This Build That. Today I’m going to show you how to make a shoe storage bench It’s a great project to wrangle all those shoes that you got laying around the house Let’s check it out and see how we did it The sides of the Bench have a modified frame and panel construction I started by cutting the legs to size from two by two material The bench is going to have a quarter inch plywood back also So I laid out a recess or a rabbit into the back legs to hold apply I made one cut to define the depth of the rabbit and then I raised the blade to match the leftover material and cleared out the rest of it with another cut You can see I went a little deeper than I needed to on that first cut but it won’t affect the function The legs are joined by a pair of side rails I started by cutting one by fours to length Then I rip them down to get two rails out of each piece that’ll be one by two After that, I drill pocket holes in the ends of all the rails Before joining the rails on the legs together I cut the side panels to size from 3/4 inch plywood I laid the legs in the rails face down and then I secured the top rail with screws Then I use the panels that I just cut to position the lower rail this eliminates any room for error and measuring and give that exact match I secure the lower rails And then I moved on to the panels I drilled pocket holes on the sides to join the legs and one on the top of the panel to attach the walnut feet later Since 3/4 inch plywood isn’t really 3/4 of an inch I use some playing cards to shim the panels up and make them flush with the inside face of the legs Then I locked everything in place with some more pocket screws The base of the bench will be painted and for a smooth surface I wanted to fill the pocket holes My intent here was to show you this cool little jig that I made to cut my own plug from dowels But as it turns out installing these plugs was a huge pain in my neck Since I couldn’t find a great way to push these in I reverted to using a scratch awl to push the plugs in bad idea Yeah, that was me. Just taking a scratch awl in the finger I got lucky there And I only escaped with just a small cut after pushing a few more of these in by hand I had an epiphany if I didn’t tuck the angle I could just cap the dowels in with a hammer This works so much better. I’ll never be cutting these angled plugs again and doing stupid things with a scratch awl After the glue dried I came back and I cut the plugs flush and then I blocked planed and sanded things smooth I also put a small chamfer on the bottom of the legs to help prevent chipping when the bench is being slid Now the whole reason I’m using three-quarter inch panels versus a floating quarter inch panel it so I could mount adjustable shelf pins I used a shelf pin jig and I drilled the holes on both sides and then I sanded the whole side assembly to 150 grit Next up I cut the parts for the lower and adjustable shelves from 3/4 inch plywood Each shelf will receive a piece of trim on the front to hide the plywood edge and give it a beefier look I need the 1 by 4 again to get the trim I cut it to size on the miter saw and then I took it back to the table saw I ran the board through to get to 1 by 2 trim pieces Then I used the trim to measure the cross cut on the lower shelf This gave me an exact match and I’ll do the same for the adjustable shelf later I drill pocket holes along the front of the lower shelf to attach the trim and along the side to attach the side assembly The ply that I was using for the shelf was a little warped from sitting in the shop for a while So I clamped it down firmly to the work surface, then I attach the trim with pocket screws the last piece I needed was a back stretcher and I cut that from the plywood as well since it’s going to be hidden and You won’t see it To attach the top I drilled three large counter bore holes with a forstner bit and the underside of the front and the back stretchers I stopped three-quarters of an inch from the other side Then I came back with a twist bit and drilled a hole all the way through the stretcher I over sized these through holes to give the screws room for wood movement later. I didn’t have a four foot clamp, so I used a makeshift clamping strip with some s clamps to pull the sides together I attached the front the back stretchers then flip the base over and attach the lower shelf I used spring clamps to position the shelf then I reference the distance between the bottom of the shelf and the bottom of the legs to make sure everything was even around the bench With everything in the right position, I attach the shelf with the pocket screws With the base assembled I cut the plywood for the adjustable shelf to width factoring in the shelf pin I cut a 1 by 4 to that same length And then I ripped it down on the table saw to the 1 by 2 sides for the trim I attached the trim the same way I did before and then I gave the shelf a little test fit To turn off the side panels I used cove molding I mitered it to fit around the inside of the panel. Then I tacked it in place with pin nailer Next I cut a back panel from quarter inch plywood and I was ready for paint I sanded everything to 150 grit then I put my first of three coats of semi-gloss latex paint on. The final two coats were done with a foam roller versus the nap roller you see here. It gives a much smoother finish Now it’s my favorite part the walnut top I picked out this huge 12 foot long board from my walnut stash and I started by breaking it down on the miter saw I cut it into three four foot sections. Which was great because it was exactly what I needed I cleaned the boards up a little bit they have a lot of dirt and bark on them So I want to make sure it was a little bit easier on my jointer and Planer knives Each board had a little bit of a cup to it as well, so I started by face joining the board making sure I had one smooth and flat side From there I went over to the planer and I flattened the other sides of the boards Until all the boards had the rough milling marks gone and had smooth surfaces on both sides If you don’t have a jointer or planer you can purchase hardwood boards already milled on all four sides at a number of different places online as well as local hardwood dealers With the boards flat and smooth on the faces, I went back to the jointer, and I milled a flat edge on each board And I finished off by taking the boards to the table saw and ripping them all to the width that I needed I ended up having to leave some sap wood on the boards but I really like the character that it gives it To join the boards together I use wood glue and a bevy of clamps no biscuits dominoes or other oddly named joinery methods are needed here I just put a few small clamps on the glue joints at the end of the boards and that helps keep everything aligned There are a few bug holes in this and I’m going to fill those with epoxy. I’m just going to mix it up It’s just some cheap stuff. I’ve got from Harbor Freight, but it’s worked well on a project I hope I have enough let’s see how it goes I mixed the two-part epoxy together and then I used a popsicle stick to fill it into the holes I ended up having just enough to cover all the repairs so it was perfect When the epoxy was dry came back with a card scraper and went over the repairs just to get everything down to a smooth surface before final surfacing From here you could go straight to an orbital Sander, but since I have a drum sander I used it for the final flattening. This thing saves a ton of time Next I took the top over to the table saw I cut it down to its final size on the Crosscut sled The top looks pretty thick at an inch and an eighth and the front edge have some voids left over from the bark removal So I decided to put a bevel on the underside of the top because this is going to help lighten the look it’s also going To help me deal with those bark voids all in one step I set the saw blade to 45 degrees then I just slid the fence so that the blade lined up with my layout lines I cut the front edge this way, and then I turned the board and cut the side bevels after removing the fence Using a chamfer bit my router would have been a much easier task here but my bit just wasn’t big enough to give the size bevel that I needed Cutting the sides was a little unwieldy and it left some burning on the bevel during the cut I used a block plane and a card scraper to remove any of the burning from the cut and to smooth everything out I finished up by sanding the whole top to 220 grit and I was ready for finish I used a satin polyurethane finish for some extra protection and some durability on this one I applied two coats that were thinned 25% and then two more coats that were thinned 50/50 with Mineral spirits I really love how this top came out. It’s just a nice warm feel to it, and I always love walnut After the top was dry put it on the base and position it for consistent reveal around the front and the sides I clamped it down with some quick clamps and then I secured it to the base through the oversized holes that I drilled earlier in the stretchers This is going to allow for that seasonal movement that I talked about as the wood on the wall up top expands and contracts I flipped the bench around and then I nailed all on the back with a brad nailer The last thing I did was install the adjustable shelf. I used those shelf pins that have a hole in them And this is so I can secure that shelf in there with some screws Because it’s going to see a lot of action of shoes going in and out So here’s what was going on in our entryway that brought on this project I love the heart pine bench that I made but it does nothing for organization but now oh yeah My wife, and I really love this project so organized If you want to build your own shoe storage bench there’s a link down below in the description That will take you to my website There’s full plans available there as well as all the materials that I use to make the project So go check it out if you’re not subscribed I’d love to have you as part of the channel Comment down below and let me know what you think about the video until next time guys get out there and build something awesome!

Related Posts

Mount Titlis Switzerland | Engelberg | Things to do

100 Replies to “DIY Shoe Storage Bench | How to Build”

  1. Brad, I found your channel today and I must say I like your style, and love your well equipped shop. I've been around for a while and may chime in every now and then to share things that have worked for me in my quest to improve my hobbies. I just watched all six of your basic turning videos before this one, all good. The main thing I noticed is your irregular use of your face mask. Seems like you trust the vacuum to take the sanding and cutting dust away from you when in fact you should ALWAYS wear your breathing protection when cutting and sanding. There will always be some fine sawdust escaping the vacuum hose, this will accumulate in your lungs with no way to get it out: on the long run your lungs will suffer dearly. Be safe and keep the chips flying.

  2. just finished mine one minor difference, the top front an rear runners where made the same height as the rear. I then added a bottom the area between them an instead of screwing the top down I added a couple hinges. Makes for a nice little storage area for gloves an mittens. I also added holes to the rear runner an bottom to allow air in when wet items area put away in the storage

  3. Great project Brad, I've just finished making this a week ago and it's has turned out pretty great. Makes such a difference to coming into the house with a nice tidy entranceway.

  4. I would like it with two front sliding doors to provide a cover for shoes to not show off.
    it definitely gives a more cleaner look !!!

  5. Need to build this so bad!!!! The entry way at my house looks like a shoe store exploded. This project looks like it is actually something a mere mortal like me could possibly do.

  6. Very nice build!!! I don't have near the tools or equipment so it'll probably take me a month, but I may try to tackle this myself!

  7. ouuuuuuuuuuuaaaaaaaaaa SUPER merci pour la vidéo franchement encore un Génie de plus du bricolages comme j'aime a bientôt pour la suite des vidéos .

  8. Liked the video. Very practical. Also perfect project for those smaller pieces of fine wood like walnut, cherry and oak. Thank you for making and sharing your video.

  9. 👏🏻👏🏻🎉👏🏻🎉👏🏻✨🌟⭐️🌟✨❤️😃❤️👍🏻👍🏻👏🏻🎉👏🏻🎉👏🏻

  10. Thanks for this video. I have build a shoe cabinet for our house based on it. I only had a jig saw to cut the plywood so you can imagine that it was quite a project 😊. Only my third one but I love the result.

  11. Tormented having to let my plants die when I die…….
    Imagine people that know they will have to let go of more things?
    Purchased, invested, given is different but having to dwell on that, or NOT thinking about it at all, how angry, I could imagine I'd be, after all the details in purchases

  12. This is an awesome video and I love the finished product. One suggestion, though. The title should be “DIY” Shoe Storage Bench. Lol

    No WAY could I do this myself.

  13. Fix This Build That
    – Nice! SUGGESTION – Can you spend more time reviewing the final product. Take a breather and slowly review the completion – zoom in from a wide shot, look at all angles – back, front, sides, top down, and even underneath. In a ten minute video spend a good minute reviewing the work of art. After all, that is the item you are "selling", in a sense, but you always skip over the most important part.

  14. OMG I LOVE THIS!!!!!!! I am definitely sharing on our social media! And, boy, would I love to see what you could do with our template tool!!!
    Emmy Braxtly

  15. This is insanely nice and very well made, just not sure if it qualifies as diy. I own 1 of the 20 tools used lol. Interested as a customer though

  16. the imperfection on the cuts are great for DIYers. probably makes them feel more comfortable if they don't cut as clean or great as Bob the Builder hehe

  17. Why did you choose to use 3/4" panel instead of 1/4" panel? Doesn't it just make the whole project heavier and cosier ?

  18. I need a storage bench for my office to hold a rackmount server and MFP. Your bench is similar in style to what I'm looking for and I think I that I can adapt it to what I need. Thanks for the inspiration!

  19. Uh….what!?! This is great. Didn’t follow any of it. I have none of these tools but still watched the whole video. Nice job!

  20. I pay already for the plans, now…I was thinking to reduce the weight and $$ by using 1/2 or less instead of 3/4 plywood, not interested in adjustable pins, but to place a fixed shelve. What else I need to adjust? ..screws length?

    (More than 2 weeks waitingfor an answer)

  21. noob question: Since this is a bench that people will sit on while putting on their shoes, shouldn't you have used dowel joints at least in order to allow for higher force/weight capacity?

  22. Awesome project! Only if real wood would be available here where I live in Asia I would have gone full on with this as a hobby BUT real wood here costs an arm and a leg plus logging is illegal.

Leave a Reply

Your email address will not be published. Required fields are marked *